7 Common Dodge RAM Backup Camera Problems In 2023(+How to Fix)

Are you continually having Dodge Ram backup camera problems but can’t seem to tell what’s going on behind the scenes? If so, don’t worry – we got your back.

As you know, the backup camera makes backing up a walk in the park.

However, if you rely too much on the backup camera, you might find it hard to park without your camera’s help.

But as you might know, a backup camera is also bound to break down at some point, just like anything else.

Here, we’ll cover some of the most common problems Dodge Ram backup cameras experience and how you can fix them.

Contents

DIY Guide: How To Fix Dodge Ram Backup Camera Problems

If you’re confused as to what’s wrong with your backup camera, don’t worry! We’re here to help you track down the issue.

Backup cameras are built to last, and it’s pretty rare when you need to replace them.

One of the important upgrades that we reviewed for you best exhaust for 5.9 cummins.

Top Selling List of Back-Up Cameras For Dodge Ram

PREVIEWBRANDDETAIL
Genuine Dodge
Dorman[Rear Park Assist]
Master Tailgaters
Master Tailgaters
PYvideo
YAOPEI

Most of the time, only doing a little bit of tweaking might fix the issue. That being said, here are seven problems that cause your backup camera to act up:

To accelerate your dodge ram performance replace bad brake pads for dodge ram 1500

01. Blue Screen

Does your screen turn blue as you try to back up the vehicle? If so, there’s probably something wrong with the fuse.

Sometimes the problem might occur when you’re driving.

The backup camera will remain on as you drive, and when you turn the vehicle, the camera goes blue.

Either way, there might be something wrong with the fuse.

Wondering how to check the fuse? Here is how you can do it:

  • Pop the hood of the truck. After that, find the fuse system, which looks just like a box
  • Once you’ve opened the box, find the RR CAMP/PARK ASSIST. Right next to the text, there should be a code that indicates where you can find the fuse for the camera
  • You should see a layout with all the codes for the fuse in the middle of the box. In our case, it’s the F95
  • Find the fuse and then take it out. If you notice that the fuse is worn-out, you must replace it. Otherwise, you’ll still get the bluescreen

To fix the issue, you need to get a new fuse, and that’s pretty much it. For more information on this topic, watch this video:

02. Cloudy Camera

Is your Dodge Ram backup camera cloudy, almost as if it’s out of focus even though you don’t see any moisture?

If that’s the case, there’s probably some dirt on the lens. A blurry backup camera is a common issue on most backup cameras.

As you go down the road, the backup camera tends to get dirty from all that dirt getting onto the camera.

If you want to clean the camera like a professional, we suggest following the steps for more information:

What You’ll Need

To make your backup camera look brand new again, you’re going to need a couple of tools for this to happen. Here is what you need to have on hands:

  • Mothers Nulens kit—the best way we’ve found to clean the backup camera is by using the excellent cleaning product from Mothers. It comes with a polishing ball, some sanding discs, and a polish
  • A microfiber towel—you’ll spray the backup camera, and to wipe it off, you need a microfiber towel
  • A drill—the kit from Mothers comes with a polishing ball, and to use it, you need a drill
  • A sprayer—the best way to apply water is by using a sprayer as you have more control over it

Spray It Down

Here, you’re going to clean the backup camera. There might be some dirt, which you want to get rid of.

The reason is, so you don’t end up buffing the backup camera with whatever dust you have. That said, follow these steps:

  • Fill the sprayer up using water. If you don’t have a sprayer on hands, you can dampen the microfiber towel, and you’ll still get the same results
  • First and foremost, you want to spray the backup camera. From there, use a microfiber towel and gently rub it against the camera.
  • You don’t want to go in the same direction. Instead, you want to rub the microfiber towel against the camera randomly. This way, you’ll hit all the cloudy spots

Sand It Down

Once you’ve cleaned the backup camera, you want to use the 3,000 grit pad as it is the best way to clean the backup camera.

  • Here, you want to use the 3,000 grit sandpaper. Keep sanding until you’ve covered the whole backup camera
  • As you’re sanding it, you’re going to see that it’s going to blur the backup camera. Don’t worry, though. It’s just the way it’s supposed to be after you’ve sanded it down

Use The Polishing Ball

Once you’ve sanded it down, you want to use the polishing ball. For this process, follow these steps:

  • Add the polish to the polishing ball. After you’ve added the polish, you want to buff the backup camera
  • Don’t forget to hit the edges as that is where it tends to look cloudy

And that’s pretty much it. You might still see some haze on the outside edges even after going through all the steps.

If that’s the case, we suggest using the microfiber towel to hit those cloudy edges.

03. Buggy Backup Camera

Does your camera look a little bit glitchy, kind of like old footage from the 80s?

There is a high chance it might have a loose or disconnected wire in the tailgate.

Sometimes, however, the buggy camera might be caused right after somebody closes the tailgate really hard.

There are several solutions to this common problem. One of the most common ones is slamming the tailgate.

While this might not sound right to some Dodge Ram owners, this method seems to fix this annoying issue immediately in some cases.

As for the solution regarding the wires, this one takes a little more effort since you’re going two need somebody else to help you during this process.

Follow these steps to fix the buggy backup camera issue:

What You Will Need

For this job, you’re going to need four tools. The process is pretty simple, and you only need a couple of minutes.

  • Tie wraps—if the wires are always moving, you’re going to need to tie wraps to ensure they won’t move carelessly as you drive, causing the backup camera to malfunction
  • A T30 bit—you’re going to remove the tailgate access panel. But before you can do that, you need to take the Torx bits off
  • A flathead screwdriver—once you’ve removed the tailgate access panel, you’re going to need something small that can get inside the tailgate access panel
  • A ratchet—since you’re going to use a T30 bit, you’re going to need a ratchet

Remove The Torx Bits

In this stage, you’re going to take the Torx bits off and then get the tailgate access panel off of the truck. For more on this, follow these steps:

  • Head over to the tailgate of your truck. From there, you want to drop it down
  • Now, here you should see all the Torx bits holding the tailgate access panel together. So, what you want to do is remove the Torx bits using your T30 bit
  • Once you’ve removed them, put them all in a pile so that you won’t lose them as you’re working on the inside of the tailgate
  • Use the flathead screwdriver to get in-between the tailgate access panel. It might be stuck, so you might want to apply some strength

Use The Tie Wraps

Here, you’re going to move the cables around until the camera looks normal again.

For that, you’re going to need to call someone to assist you during this process. That being said, please follow the steps down below:

  • Have somebody inside the truck looking at the screen. From there, you want to move the wires until the camera does not look weird anymore. This might take some time before you get the right spot
  • Once you know the camera is working, you want to wrap the wires using tie wraps. This way, they won’t move as you drive
  • And now, you have to put everything back on

You’ve done it; you have fixed the buggy issue. The extra play in the wires was causing this annoying problem all along.

The process is pretty simple, and you only need a few minutes to fix the backup camera.

04. Green Lines All Over The Screen

One of the most common problems for the backup camera problems on Ram 1500 is weird green lines on your screen as soon as you put the truck in reverse.

Sometimes, the green lines might not be so persistent, and they might go away.

If you’re in a similar situation, you might be able to fix this issue by resetting the camera.

This issue is quite hard to track down as several culprits could cause the camera to work poorly.

For instance, sometimes you might only see the green lines on the backup camera but not on the navigation panel.

And sometimes, it might go back to normal. It just happens randomly.

So, we’re going to fix that issue by performing a software reset. To reset the backup camera, follow these steps:

Disconnect The Battery

The first method that you want to try out to reset the backup camera is to disconnect the battery.

While this might not work for some people, this might be what you’re looking for.

So, to reset the backup camera back to the factory settings, follow these steps:

  • Pop the hood of your truck. After that, unhook the battery of your vehicle
  • Leave it unhooked for 30 minutes so it will reset the camera

That is plenty of time for the backup camera to go back to factory settings.

After that time has passed, the green lines should be gone.

Turn The Ignition On

If the previous method doesn’t do the trick, we have another one that might work.

  • Get in the truck and then make sure to close all the doors
  • Turn on the ignition, but don’t start the vehicle just yet
  • On the screen, tap on the upper right-hand corner and hold your finger down for nearly 20 seconds. After that, you want to turn the ignition off and then turn it back on.
  • And finally, start your vehicle. That’ll reset your backup camera

This last method is a little bit more complicated than the previous one. However, if the first one didn’t do the trick for you, this might be the one you’re looking for.

05. Backup Camera Stays On

Have you been driving for the past 30 minutes, but your camera is still on?

You’ve probably tried to put the truck in reverse to see if it would reset the camera but noticed that it wasn’t of any help.

There are a couple of methods you could try to fix this somewhat annoying issue.

I mean, you probably don’t want the screen to continue to display all those lines when you put the truck in reverse.

You could get distracted by always looking at the backup camera as you drive.

That said, here are two methods you can try to fix the backup camera:

  • Disconnect the battery. Leave it unhooked for at least 30 minutes. Also, disconnect the negative side first
  • If that didn’t work, you should unplug your phone. If you recently plugged in your smartphone to use the android auto, that might be the culprit. After you’ve disconnected your phone, everything should go back to normal

Those methods are the most common ways that you can use to fix your backup camera.

If that doesn’t quite work for you, you could give the other methods a shot and see if you can find the culprit.

06. Intermittent problem

Is your Ram backup camera distorted? Another common problem that backup cameras experience is a constant signal loss.

Sometimes, you might get through a full night of driving and no issues whatsoever.

However, on some days, the screen might lose signal when you put the truck in reverse.

So, what is the culprit? Some Dodge Ram owners have reported that the intermittent problem might go away after updating the system.

But others have claimed that the problem goes away for a while just to come back a few months down the line. So, your best bet might be updating the software.

07. Camera Does Not Work Anymore

Some Dodge Ram owners have claimed that their cameras randomly stopped working as they were going on with their days.

For example, when they put their trucks in reverse, they simply get a black screen with a message.

If you’re in a similar situation, here is what you can do to fix this annoying problem with your Dodge Ram:

What You’ll Need

This is a simple fix that can be done by anybody. You’re only going to need a T30 bit to remove the tailgate access panel.

Additionally, you can use a flathead screwdriver to remove the tailgate access panel if you’re having a hard time pulling it out.

Plug-In The Connector

In this section, you only want to reconnect the connector of your backup camera. Here is what you must do to reconnect the connector:

  • Here, you want to remove the Torx bits from the tailgate access panel.
  • Once you’ve removed the Torx bits, you might have to use a flathead screwdriver to get inside the tailgate access panel to pull it out
  • Now that you got the tailgate access panel out of the way, go ahead and find the connector and plug it back in

Your backup camera should now be working just fine.

Sometimes as you drive down the road, all the movement might make the connector come loose, which is why your backup camera stopped working in the first place.

Luckily for you, this is a super easy fix.

DIY Guide: How To Install A Backup Camera On Dodge Ram

If you’ve determined that it might be best to replace the backup camera, then you’re in the right place.

Here, we’ll walk you through all the steps required to replace your damaged backup camera.

Without any further ado, let’s take a look at all the steps needed for the installation!

What You’ll Need

We’re going to be replacing the damaged backup camera, and for this job, you’re going to need the following tools:

  • A T30 bit—when removing the tailgate, you’re going to need the t30 bit to remove the bolts
  • A T20—the bolts on the backup camera must be removed using a T20 bit
  • A drill—we suggest using a drill to remove the bolts as it’s way easier
  • A quarter-inch ratchet—you’re going to need a small ratchet to reach the backup camera

01. Remove The Tailgate Access

So, before you can access the camera, you have to remove the tailgate access panel. To remove the cover, follow these steps:

  • Drop the tailgate all the way down
  • Now you want to use the T30 bit to remove the Torx bits holding the cover together
  • After you’ve removed the cover, you should see the old camera inside the tailgate

02. Unplug The Connector

Ok, so now that you got the tailgate access panel out of the way, you have to unplug the connector.

And then, you must remove the bolts on the backup camera.

  • There are two Torx bits you have to remove; they are quite hard to remove, to say the least. You might not be able to get in there with a ratchet
  • If you do manage to reach the Torx bits, you want to loosen them and then spin them out by hand as it’s a lot easier that way
  • Once you get the last bolt out, you want to take the old backup camera and pull it out

03. Install The New Backup Camera

Installing the backup camera is the final step. To install your new backup camera, follow these steps:

  • Now that you’ve removed the old backup camera proceed to install the new one. For that, you’re going to need to reinstall the Torx bits you previously took off
  • The old clip of the backup camera is still inside; you want to pull it out before installing the other side of the camera. After that, plug in the new connector
  • There are two holes inside the tailgate; that is precisely where you want to install the other side of the new backup camera
  • Keep pushing it down until you’ve got it in place. After that, put everything back together

And that’s all there is to it. This process barely takes any time, and you save up lots of money just by doing it on your own.

If you want to watch a video on this simple process, we suggest giving this well-made video a try:

Frequently Asked Questions (FAQs)

Are you looking for more information about backup cameras?

Well, here are some common questions that might help you:

How much does it cost to have a backup camera installed?

You have to take into account whether you have a screen or not.

If you simply need a backup camera, it would probably be around $500.

However, if you need a screen, add an additional 200$ to the previous total.

How do you fix a blurry backup camera?

Here is the best way to fix a blurry backup camera:

  • Dampen a microfiber towel
  • Rub it against the backup camera
  • Be careful, though. You don’t want to apply too much pressure

Is a backup camera worth it?

Yes, a backup camera is worth the money. If you drive a truck, you definitely need a backup camera when you put it in reverse.

How long does it take to install a backup camera?

Most of the time, it takes about 40 minutes. If you’ve done it before, it might take less time.

Conclusion

There are plenty of Dodge Ram backup camera problems, and sometimes it might be hard to find the culprit.

But if you’re willing to fix your backup camera on your own, you have to put in a little bit of time to find the culprit.

And if you resolved the issue on your own, you’d save up much money.

Sometimes the problem can be fixed by merely tweaking some wires or updating the software.

However, sometimes you might have to replace the backup camera, but that rarely happens unless a tree fell on the camera.

Either way, fixing your backup camera shouldn’t take more than a few hours. So, what are you waiting for to do it?

georgelawsongallery.com is a participant of the Amazon Affiliate program. We may earn a small commission if you purchase through our recommended links. More details.

Leave a Comment